Scientific-molding calculators: viscosity curve, gate seal, cavity balance, Cpk and gage R&R.
Connect Remote server
claude mcp add --transport http lab https://www.futuremicromoldllc.com/api/mcp
{
"mcpServers": {
"lab": {
"url": "https://www.futuremicromoldllc.com/api/mcp"
}
}
}
{
"servers": {
"lab": {
"type": "http",
"url": "https://www.futuremicromoldllc.com/api/mcp"
}
}
}
Settings > Connectors > Add custom connector
URL: https://www.futuremicromoldllc.com/api/mcp
Tools 11 found in our last check
viscosity_curveFind the optimal injection velocity from a velocity / peak-pressure sweep. Computes relative viscosity (plastic pressure times fill time) against relative shear rate, locates the shear-thinning plateau, and picks a velocity from the middle of it. Record a fill time on every poin…
cavity_balanceQuantify cavity-to-cavity fill imbalance from short-shot weights. Give two or more replicate shots at a fill level and the result also says whether the variation comes from the cavities (runner and gate geometry) or from shot-to-shot process drift — the two have opposite fixes.…
pressure_dropFind where injection pressure is consumed along the flow path. Each reading is the CUMULATIVE peak pressure needed to fill through that section — an air shot gives the nozzle figure, then sprue, runner, gate and the full part — so the values ascend. Known sections: Nozzle, Sprue…
cosmetic_windowMap which combinations of two process parameters produce a cosmetically acceptable part, and how much room surrounds the centre. Sweep wider than you expect the window to be: a passing point on the edge of the range tested means the window was never closed on that side. Axes and…
gate_sealFind the hold time at which the gate freezes and part weight stops rising. Seal is the first of three consecutive weights within 0.1% of each other; the recommended production hold time adds a margin of one increment. A weight that falls back after seal means the gate did not st…
cooling_timeFind the shortest cooling time at which a dimension has stopped changing, and the cycle seconds that come off. Supply the drawing tolerance and the rule tightens to a tenth of it. Measure each part at a consistent interval after ejection — the part keeps moving.
process_capabilityJudge whether a running process can hold a dimension inside its tolerance. Reports Cp and Cpk from within-subgroup sigma and Pp and Ppk from overall sigma — the second pair is what a customer's SPC package computes from the same measurements — each with a 95% confidence interval…
gage_rrRate a measurement system from a crossed study: every operator measures every part, the same number of times. Two-way ANOVA per the AIAG Measurement Systems Analysis manual (4th ed.), matching Minitab's crossed gage R&R defaults: the operator × part interaction is pooled into re…
get_study_protocolReturn the full procedure for one study: what it is for, the equipment needed, the step-by-step method at the press, and what a good result looks like, so the numbers collected at the press are the ones the calculation needs.
plan_process_developmentGiven the studies already run, return the full development sequence with each one marked done or outstanding, what each fixes, what it depends on, and which study to run next. The order matters: each study fixes a setpoint the next one holds constant, so running them out of orde…
open_study_sheetOpen an empty data sheet for one study in an interactive card: the procedure beside a table the person fills in or pastes into, with the result computed as they type. Also returns the procedure as text and a link to the same calculator on the Lab website.
Details
| Endpoint | https://www.futuremicromoldllc.com/api/mcp (Streamable HTTP) |
| First published | 16 Nov 2026 |
| Last updated | 16 Nov 2026 |
| Registry name | com.futuremicromoldllc/lab |
More other servers See all
Listing data from the official MCP registry. Status and tools from NestDaddy's daily check. Browse all MCP servers.
