88 free engineering calculators: RF link budgets, LoRa/Meshtastic, PCB, solar, homelab. Keyless.
Connect Remote server
claude mcp add --transport http calc https://calc.engineer/mcp{
"mcpServers": {
"calc": {
"url": "https://calc.engineer/mcp"
}
}
}{
"servers": {
"calc": {
"type": "http",
"url": "https://calc.engineer/mcp"
}
}
}Settings > Connectors > Add custom connector
URL: https://calc.engineer/mcpTools 80 found in our last check
fsplCalculate free-space path loss (FSPL) in decibels using the ITU-R P.525 standard formula. Given a frequency in MHz and distance in kilometres, returns the expected signal attenuation in an ideal line-of-sight radio link with no obstacles, reflections, or atmospheric absorption.…
link_budgetCompute a full RF link budget from transmitter power, frequency, distance, and antenna gains. Calculates EIRP, free-space path loss (ITU-R P.525), received power at the receiver, and link margin relative to an optional receiver sensitivity threshold. Use this to determine whethe…
dipoleCalculate physical dimensions of a dipole antenna for a given frequency. Returns half-wave or quarter-wave element length in metres, feet, and inches. A half-wave dipole is the most common resonant antenna with approximately 2.15 dBi gain. A quarter-wave monopole (ground plane a…
microstripCalculate PCB microstrip trace width for a target characteristic impedance using the Hammerstad-Jensen closed-form equations. Given target impedance (Z0), substrate dielectric constant (er), substrate height, and copper weight, returns the required trace width and effective diel…
dbm_convertConvert a power level in dBm to milliwatts, watts, dBW, and RMS voltage across a given impedance. dBm is the standard unit for RF power referenced to 1 milliwatt. This tool is essential when interfacing datasheets (which use dBm) with circuit analysis (which uses volts and watts…
noise_figure_cascadeCalculate the cascaded noise figure of a multi-stage receiver chain using the Friis formula. Each stage has a noise figure and gain in dB. The first stage dominates overall system noise, which is why low-noise amplifiers (LNAs) are placed at the front of the chain. Returns total…
vswrConvert between VSWR, return loss, and reflection coefficient — provide any one parameter and get all related impedance-mismatch metrics. Computes VSWR (voltage standing wave ratio), return loss in dB, reflection coefficient (gamma), mismatch loss, and percentage of power reflec…
attenuator_piDesign a Pi-topology resistive attenuator pad. Given a desired attenuation in dB and characteristic impedance (default 50 ohm), computes the three resistor values for a symmetrical Pi-pad network. The Pi attenuator uses two shunt resistors (R1, R3) and one series resistor (R2).…
attenuator_teeDesign a Tee-topology resistive attenuator pad. Given a desired attenuation in dB and characteristic impedance (default 50 ohm), computes the three resistor values for a symmetrical T-pad network. The Tee attenuator uses two series resistors (R1, R3) and one shunt resistor (R2).…
fresnel_zoneCalculate the Fresnel zone radius at the midpoint of a radio link. Given frequency in MHz, link distance in kilometres, and zone number (1-5), returns the Fresnel zone radius in metres and feet, plus the 60% clearance threshold used in practical link engineering. The first Fresn…
wavelength_freqConvert between radio frequency and wavelength. Provide either frequency in MHz or wavelength in metres, and get the full set of equivalent values: frequency in MHz and GHz, wavelength in metres, centimetres, millimetres, and feet. Essential for antenna dimensioning, waveguide s…
spice_templateGenerate a complete SPICE netlist from a parameterized template. Supports common circuit topologies: low-pass RC filter, voltage divider, common emitter amplifier. Returns a ready-to-simulate netlist string that can be passed directly to spice_simulate. Use this when an agent ne…
spice_simulateRun a SPICE circuit simulation directly in the worker. Accepts a standard SPICE netlist and performs operating-point (.op), DC sweep (.dc), AC frequency sweep (.ac), or transient (.tran) analysis using a built-in modified-nodal-analysis engine with Newton-Raphson nonlinear solvi…
lora_airtimeCalculates LoRa packet time-on-air using the Semtech AN1200.13 formula. Computes symbol duration, preamble time, payload symbol count, effective data rate, and the minimum transmission interval for 1% duty cycle compliance. Essential for capacity planning in LoRaWAN and Meshtast…
snr_marginComputes LoRa link SNR margin by comparing received power against the noise floor and the spreading-factor-dependent demodulation threshold from the Semtech SX1276 datasheet. Calculates receiver noise floor from thermal noise (-174 dBm/Hz), channel bandwidth, and receiver noise…
channel_utilizationEstimates Meshtastic or LoRa mesh channel utilization percentage based on node count, message rate, and per-packet airtime. Determines how much of the shared radio channel is occupied and computes the maximum number of nodes before exceeding a configurable duty cycle limit (defa…
lora_range_estimateEstimates LoRa maximum communication range by computing the free-space path loss (FSPL) link budget and applying terrain-dependent correction factors. Calculates total link budget from transmit power, antenna gains, and receiver sensitivity, then solves the FSPL equation for dis…
lora_sensitivityCalculates LoRa receiver sensitivity from spreading factor, bandwidth, and noise figure using the Semtech SX1276 datasheet SNR thresholds. Computes the noise floor from thermal noise density (-174 dBm/Hz), channel bandwidth, and receiver noise figure, then adds the spreading-fac…
duty_cycle_budgetCalculates LoRa duty cycle budget for EU868, US915, AS923, and AU915 regulatory regions. Computes maximum messages per hour, minimum transmission interval, and effective data rate under regional duty cycle constraints. EU868 and AS923 enforce 1% duty cycle (ETSI); US915 has no d…
meshtastic_rangeEstimates Meshtastic node communication range using real hardware profiles and firmware channel presets. Combines device-specific TX power and antenna gain (Heltec V3, RAK WisBlock, T-Beam, T-Beam Supreme, Station G2) with firmware modem presets (Long Fast, Long Slow, Very Long…
eirp_complianceChecks EIRP (Effective Isotropic Radiated Power) compliance against regional regulatory limits for LoRa and Meshtastic operation. Computes EIRP from transmit power, antenna gain, and cable loss, then compares against FCC (US, 36 dBm), ETSI (EU, 16.15 dBm), ACMA (Australia, 30 dB…
meshtastic_powerCalculates Meshtastic node power consumption and battery runtime using device-specific power profiles and firmware role-based duty cycling. Models sleep, RX, and TX current draw for Heltec V3, RAK WisBlock, T-Beam, T-Beam Supreme, and Station G2 with GPS, BLE, and display periph…
lora_param_optimizerRecommends optimal LoRa spreading factor, bandwidth, and TX power based on target range, terrain, and optimization priority. Iterates through all SF (7-12) and BW (125/250/500 kHz) combinations, computing achievable range, airtime, data rate, and battery impact for each. Ranks c…
zfs_capacityCalculate usable ZFS pool capacity for any RAID level including stripe, mirror, raidz1, raidz2, and raidz3. Computes raw capacity, parity overhead, data disk count, usable terabytes after ZFS metadata overhead (checksums, block pointers, uberblocks), and storage efficiency perce…
zfs_ramCalculate recommended RAM and ARC sizing for a ZFS storage pool based on workload type, pool size, deduplication status, and L2ARC cache size. Computes minimum and recommended RAM in gigabytes, ARC target size, and dedup table overhead. Accounts for workload-specific IO patterns…
tcp_throughputCalculate maximum TCP throughput using the Bandwidth-Delay Product (BDP) formula. Given link bandwidth and round-trip latency, computes the BDP (maximum in-flight data), achievable throughput with a given TCP window size, link utilization percentage, and recommended window size…
wireguard_mtuCalculate the optimal MTU for a WireGuard VPN tunnel interface with a detailed overhead breakdown. Accounts for WireGuard header (32 bytes), outer IP header (20 bytes IPv4 or 40 bytes IPv6), UDP header (8 bytes), and optional PPPoE encapsulation (8 bytes). Prevents fragmentation…
subnet_calculatorCalculate IPv4 subnet details from CIDR notation. Parses a CIDR block (e.g. 192.168.1.0/24) and returns the network address, broadcast address, subnet mask, wildcard mask, first and last usable host addresses, total and usable host counts, prefix length, and classful IP class (A…
raid_iopsEstimate RAID array IOPS performance and latency for ZFS and traditional RAID configurations. Calculates maximum read IOPS, write IOPS (accounting for write penalty/amplification per RAID level), blended IOPS for a configurable read/write workload mix, and rough per-disk latency…
power_costCalculate total power consumption, electricity cost, and circuit requirements for a homelab. Enter each device's wattage to get daily/monthly/yearly kWh and cost at your local electricity rate. Accounts for cooling overhead via PUE (Power Usage Effectiveness). Shows amperage dra…
cooling_btuEstimate the cooling load (BTU/hr) for a homelab or server closet based on equipment wattage, room dimensions, insulation quality, and solar exposure. All electrical power converts to heat — this tool calculates equipment heat output, envelope heat gain through walls, and solar…
rack_capacityQuick rack space and weight sizing calculator for homelab and small data center racks. Enter your devices with their height in rack units, weight, and wattage to get total utilization, remaining free space, weight totals in lbs and kg, and recommended PDU count based on the NEC…
network_bandwidthPlan and validate network link capacity for homelab workloads. Determine whether a 1G, 2.5G, 10G, or faster link can handle your concurrent streams (VMs, backups, media, iSCSI). Calculates effective bandwidth after TCP/IP overhead, total required bandwidth, utilization percentag…
thermal_enclosureEstimate steady-state thermal behaviour of a rectangular enclosure (server rack, electronics housing, equipment cabinet) using a lumped-parameter energy balance with natural-convection and radiation correlations, or forced-flow air energy balance. Accepts enclosure dimensions, h…
heatsink_cfdAnalyze a forced-convection fin-array heatsink using established channel-flow correlations (developing laminar Nusselt, fin efficiency tanh(mH)/mH, parallel-plate friction). Computes base-to-air thermal resistance, pressure drop, base and fin-tip temperatures, fin efficiency, an…
pcb_thermalEstimate PCB component temperatures by solving a thermal resistance network (thermal↔electrical analogy) with the built-in MNA solver. Each component gets a junction node (package θjb from a typical-datasheet table), a local board node coupled to its neighbours through in-plane…
battery_lifeCalculates battery runtime and energy capacity given cell capacity in mAh, nominal voltage, and average current draw. Accounts for real-world discharge efficiency (Peukert-adjacent derating) to produce effective capacity, total energy in Wh, and runtime in hours and days. Useful…
wire_gaugeDetermines the minimum AWG (American Wire Gauge) conductor size for a given current, voltage, one-way cable distance, and maximum allowable voltage drop percentage. Supports copper and aluminum conductors. Computes round-trip resistance, actual voltage drop in volts and percent,…
solar_sizingSizes an off-grid solar power system by calculating the number of panels and battery bank capacity required for a given daily energy consumption. Accounts for system losses (inverter, wiring, charge controller), battery depth-of-discharge, and autonomy days for cloudy weather. O…
ups_runtimeEstimates UPS (Uninterruptible Power Supply) backup runtime from battery specifications and connected load. Takes VA rating, watt rating, load in watts, and battery configuration (count, voltage, amp-hours) to compute effective stored energy after efficiency losses and runtime i…
mah_to_whConverts battery capacity from milliamp-hours (mAh) to watt-hours (Wh), kilowatt-hours (kWh), and joules (J) given the nominal cell voltage. This is the most common battery unit conversion needed when comparing cells rated in mAh (e.g. 18650, AA) against energy budgets specified…
watts_to_ampsConverts electrical power in watts to current in amps (and milliamps) for a given voltage, using the DC power formula P = V * I. Also computes the implied load resistance via Ohm's law (R = V / I) assuming a purely resistive load. This is the most common electrical conversion fo…
voltage_dropCalculates voltage drop across a conductor run given current, wire length, AWG gauge, system voltage, and conductor material (copper or aluminum). Computes round-trip resistance, voltage drop in volts and percent, voltage at the load end, power dissipated in the wire, and NEC co…
battery_charge_timeEstimates battery charge time given capacity in mAh, charge current in mA, charger efficiency, and initial state of charge. Accounts for real-world charging losses (typically 80-90% efficient) to produce time in hours and minutes, energy required in Wh (at an optional voltage, d…
solar_load_auditCalculates total daily energy consumption from an appliance list — the critical first step before sizing solar panels or batteries. Enter each appliance with its wattage, hours of daily use, and quantity. Outputs total daily kWh (with configurable safety margin for surge and inr…
solar_roiCalculates solar system return on investment, payback period, and levelized cost of energy (LCOE). Models year-by-year savings accounting for panel degradation, utility rate inflation, federal Investment Tax Credit (ITC), state rebates, and annual maintenance. Outputs net cost a…
battery_autonomyCalculates how many days a battery bank can sustain loads without solar input — critical for off-grid and backup power sizing. Accounts for depth of discharge, round-trip efficiency (lithium vs lead-acid), minimum state of charge, and optional partial solar contribution during c…
string_sizingCalculates optimal solar panel string and MPPT configuration based on panel electrical specs, inverter/charge-controller MPPT limits, and site temperature extremes. Applies temperature coefficients to determine Voc at minimum temperature (cold) and Vmp at maximum temperature (ho…
generator_offsetCompares total cost of ownership between a fuel generator and a solar+battery system over a configurable time horizon. Calculates yearly and cumulative costs for generator-only, solar-only (amortized), and hybrid scenarios. Accounts for fuel cost, generator consumption rate, mai…
wire_ampacityDetermine minimum wire gauge using NEC Table 310.16 ampacity ratings with full derating. Looks up base ampacity for copper or aluminum conductors at 60°C, 75°C, or 90°C insulation rating, then applies NEC 310.15(C)(1) ambient temperature correction and NEC 310.15(C)(2) conductor…
inverter_sizingSize a DC-to-AC inverter for off-grid solar, battery backup, or mobile power systems. Computes the required continuous VA rating from total load watts and power factor, estimates surge capacity for motor-starting loads (3-7x rated power), applies NEC-recommended 20% derating for…
pcb_layoutTurn a SPICE netlist into a fab-ready 2-layer PCB: assigns real footprints (0805, TO-92, DO-35, DIP-8, headers, LED, radial-cap), auto-places components (connectivity-aware; or use your own placement), routes a 2-layer maze router with vias, and VERIFIES the result with DRC (cle…
voltage_dividerCalculates output voltage, current draw, and power dissipation for a resistive voltage divider. Given an input voltage Vin and two resistor values R1 (upper) and R2 (lower), computes Vout = Vin * R2 / (R1 + R2), divider current, individual resistor power dissipation, and the div…
rc_filterComputes the cutoff frequency, time constant, impedance, and phase shift of a first-order RC filter. Supports both lowpass and highpass topologies. The cutoff frequency is f = 1/(2*pi*R*C) where the signal is attenuated by 3 dB. The time constant tau = R*C governs transient resp…
lc_resonanceCalculates the resonant frequency of an LC circuit, along with optional Q factor and bandwidth when series resistance is provided. The resonant frequency f0 = 1/(2*pi*sqrt(L*C)) is where inductive and capacitive reactances cancel. Used for designing tank circuits, oscillators, b…
impedance_matchDesigns an L-network impedance matching circuit between two real impedances at a given frequency. Computes the required shunt and series reactive components (inductor and capacitor) to transform the source impedance to the load impedance. The network Q factor is sqrt(Rh/Rl - 1)…
trace_widthCalculates the minimum PCB trace width for a given current using the IPC-2221 standard formula. The IPC-2221 empirical equation relates current capacity to cross-sectional area and temperature rise: I = k * dT^0.44 * A^0.725, where k=0.048 for external layers and k=0.024 for int…
ohms_lawSolves Ohm's Law and the power equation given any two of four electrical quantities: voltage (V), current (I), resistance (R), and power (P). Uses V=IR, P=VI, P=I^2R, and P=V^2/R to derive the missing two values. Fundamental for every circuit design task: sizing resistors, estim…
resistor_color_codeDecodes 4-band or 5-band resistor color codes into resistance value, tolerance, and min/max range. Accepts an ordered array of color names (left-to-right as printed on the resistor body). Supports standard EIA color codes including gold and silver multiplier/tolerance bands. Out…
led_resistorCalculates the current-limiting resistor for driving one or more LEDs in series from a DC supply. Computes the exact resistance from R = (Vsupply - n*Vf) / I, then selects the nearest E24 standard resistor value. Reports the actual current with the standard resistor, power dissi…
timer_555Calculates timing parameters for the ubiquitous NE555 / LM555 timer IC in astable (free-running oscillator) and monostable (one-shot pulse) modes. In astable mode, computes frequency, period, duty cycle, and HIGH/LOW durations from R1, R2, and C using f = 1.44 / ((R1 + 2·R2) · C…
op_amp_gainCalculate voltage gain and output for operational amplifier circuits in inverting, non-inverting, and differential configurations. For inverting: Av = -Rf/Ri with input impedance equal to Ri. For non-inverting: Av = 1 + Rf/Rg with very high input impedance. For differential: Av…
capacitor_chargeCalculates RC capacitor charge timing, energy storage, and transient voltages. Given resistance, capacitance, supply voltage, and optional initial voltage, computes the RC time constant (τ = R×C), time to reach standard charge thresholds (63%, 86%, 95%, 99%), voltage at key time…
pcb_via_currentCalculate PCB via current-carrying capacity using the IPC-2221 standard. A plated via is a hollow copper cylinder whose cross-sectional area is the annular ring of plating: A = pi * (D - t) * t, where D is the drill diameter and t is plating thickness. The IPC-2221 empirical for…
power_supply_decouplingSelect bypass and bulk decoupling capacitors for IC power supply pins. Computes the target PDN (Power Distribution Network) impedance from supply current, voltage, and allowable ripple using Z_target = V_ripple / I_total. Recommends a ceramic bypass capacitor (high-frequency dec…
log_calcCompute logarithms of a positive number in any base. Returns the custom-base logarithm, natural logarithm (ln), common logarithm (log10), and binary logarithm (log2). Useful for signal processing (decibel calculations), information theory (entropy in bits), pH chemistry, and gen…
sig_figsCount significant figures in a number and optionally round to N significant figures. Accepts the number as a string to preserve trailing zeros (e.g. '1.200' has 4 sig figs). Applies standard sig fig rules: leading zeros do not count, trailing zeros after a decimal point count, t…
scientific_notationConvert any number to scientific notation and engineering notation. Returns the coefficient, exponent, a formatted string with Unicode superscripts (e.g. '3.14 × 10²'), and engineering notation where the exponent is a multiple of 3. Useful for expressing very large or very small…
percentage_calcCalculate what percentage one number is of another. Given a value and a total, returns the percentage, decimal form, and simplified fraction. For example, 3 out of 4 yields 75%, 0.75, and '3/4'. Commonly used for test scores, survey results, financial ratios, completion rates, a…
percentage_increaseCalculate the percentage change between an old value and a new value. Determines whether the change is an increase or decrease, the absolute change, and the percentage change. Essential for financial analysis (stock price changes, revenue growth), scientific measurements (before…
exponent_calcCompute the result of raising a base to an exponent (base^exponent). Handles positive and negative exponents, fractional exponents, and zero. Returns the numeric result and a scientific notation string for very large or very small results. Useful for compound interest calculatio…
square_rootCompute the square root of a non-negative number. Returns the decimal result, whether the input is a perfect square, and a simplified radical form (e.g. '√12' simplifies to '2√3'). For integer inputs, factors are extracted from under the radical sign. Useful for geometry (diagon…
circumferenceCalculate the circumference and area of a circle given either a radius or diameter. Provide one or both; if both are given, radius takes precedence. Returns circumference (C = 2πr), area (A = πr²), and both radius and diameter for completeness. Common in mechanical engineering (…
slope_calcCalculate the slope, y-intercept, line equation, angle, and distance between two points in a 2D Cartesian plane. Given coordinates (x1, y1) and (x2, y2), computes slope (rise/run), y-intercept, the equation in slope-intercept form (y = mx + b), angle in degrees relative to the x…
pythagorean_theoremSolve for any side of a right triangle using the Pythagorean theorem (a² + b² = c²). Provide any two of the three sides (a, b, c) and the missing side is computed. Also returns the triangle area (0.5 * a * b), perimeter, and confirms it is a right triangle. Side c is always the…
p_valueCalculate the p-value for a z-score or t-statistic. Supports one-tailed (left or right) and two-tailed hypothesis tests using either the standard normal distribution or the Student's t-distribution when degrees of freedom are specified. Returns significance flags at the 0.01, 0.…
confidence_intervalCalculate the confidence interval for a sample mean. Given a sample mean, sample size, standard deviation, and confidence level, computes the margin of error, lower and upper bounds, critical z-score, and standard error. Supports finite population correction (FPC) when a populat…
sales_taxCalculates total cost including sales tax for a purchase. Given a unit price, tax rate percentage, and optional quantity, computes the subtotal (price times quantity), the tax amount rounded to two decimal places, and the final total. Useful for estimating purchase costs across…
salary_to_hourlyConverts compensation between annual salary, monthly pay, weekly pay, and hourly wage. Accepts any of the four pay periods as input and derives all others. Uses configurable hours per week (default 40) and weeks per year (default 52). Daily rate assumes an 8-hour workday; monthl…
loan_amortizationComputes a full loan amortization schedule given principal, annual interest rate, and term in months. Returns the fixed monthly payment, total interest, total payments, and a month-by-month breakdown of principal vs interest. Supports optional extra monthly payments — shows mont…
Details
| Endpoint | https://calc.engineer/mcp (Streamable HTTP) |
| First published | 18 Jul 2026 |
| Last updated | 18 Jul 2026 |
| Registry name | engineer.calc/calc |
More developer tools servers See all
Listing data from the official MCP registry. Status and tools from NestDaddy's daily check. Browse all MCP servers.